Pages

If you find this article useful and can afford to donate please do!

Tuesday, January 24, 2012

Wire Jewelry Step by Step : Mother

Posted by consxavier | Tuesday, January 24, 2012 | Category: , , , , , , , , , |

Wire Jewelry Step by Step : Mother

Before I start the lessons, you need to know a few things.

1. The wire can not be too soft. If you start with the soft wire, your names are not
    going to be easy to make them latter on. 28 g. round is good.

2. If you use sq. wire you need to pay attention every time you bend it because it will
    twist, for sure. {In this case you need square nose pliers to untwist it}

3. Always pinch the wire from the back when bending.
    Do not unbend (Go back to do it better} because it will brake

4. Make sure your work is flat and even while you are working the piece otherwise is
    going to be difficult to do it later.

5. Get 15 inches of wire so you practice more than once.

6. Be patient, maybe the first few times is not what you expect but practice will get
    you there. {My first one looked like a license plate in zig zag big and uneven}

Now here we go on the wire name lessons:


        Lesson #                    Description
       One                     Amy
       Two                    Beth
       Three                  Mother
       Four                   Cindy
       Five                    Diane
        Six                      Evelyn
     Seven                 Ruby
     Eight                  Frida

TUTORIAL 3: "Mother" Pendant 

1. Start about 1½ inches from the end of the wire, turning the long piece of the wire to the
    front of the pliers; make a loop {one complete circle}.

2. Working on the long piece of the wire; pinch a little less than ½ of an inch and bend to
    the back.

3. Press it down at the top, roll the top to the right just a little bit. You are rolling two wires
    together (picture #1 in tutorial #1) 



4. Grasp the wire at the top and pull it to the right, a little bit.

5. Grasp the wire at the middle, and bend it back and up, pinch a little; pull it to the right.

6. Grasp the wire at the top even with the first part of the “M” and bring it down; pinch at
    the top ( you made the “M”)

7. Grasp the wire at the bottom even with bottom of the “M” and bring it up

8. Grasp it about half way from the “M” , bring it down to the right to make a hump 
    (see picture #1)



9. Grasp the wire from the back at the bottom and bring it up through the front 
    (see picture #2)


10. Grasp the wire at he back; on the left side of the circle and bend it to the right
     ( see picture #3) you are making the “o”



11. Leave the pliers there and bring wire to the left and down to make the “o”
      (see picture #4)


12. Grasp the two wires at the bottom and through the “o” bring it up (see picture #5)


13. Grasp it at the top even with the “M” and bend it to the back.; pinch it at the top.

14. Grasp it from the back at the tip; bend it to the right.

15. Grasp the wire that you just bend, an bring it around the pliers and the wire; to the
      front of the “t” you are making the cross of the “t” (see pictures in tutorial #2)



16. Grasp it at the back and bend it down and hide it behind (carefully pinch the cross of
      the “t'” ) making sure is even and you do not see the back wires.

17. Grasp it at the bottom of the “t' and bend it up.

18. Grasp the wire even with the top with the “t” bend it down and to the front looks like
      an “L”.

19. Grasp it at he bottom and bend it up, toward you and pinch it a little.

20. Grasp it in the back about the level of the “o” and bend it to the right, to make a hump
      you made the “h”.

21. Grasp the wire at the bottom and bring it up; grasp it even with the “o” and bring it
      down through the front to make the “e”.


22. Grasp it at the bottom and bring up, (grasp it even with the “e”) and bend it back and
      down, pinch it at the very top and bring it up.

      Grasp it close to the bend top and bring down (see picture #6) you have the “r” Grasp
      it at the bottom through the back and bring it up



Congratulations: You finish the pendant: MOTHER.

Now; take the end; grasp it a little higher than the tip of the “M” (
look at the picture for reference) and bend it up, fold it back and around the
pliers twice, to form a double loop; then around the wire twice to finish it;
cut the excess in the back.

This is for the chain; do the same with the piece of wire that you left in the very beginning.
Finish filing the ends and carefully crimp the ends.

Polish it a little and Enjoy it!!!



Cut the extra wire in the first loop, make it look like a heart. Fold the wire to make a loop
to hang do it twice. Put it on the name.

        Lesson #                    Description
       One                     Amy
       Two                    Beth
       Three                  Mother
       Four                   Cindy
       Five                    Diane
        Six                      Evelyn
     Seven                 Ruby
     Eight                  Frida

HOT OFFER!

You can have all the skills under your belt that you need in this ebook to make a constant $1,574 a week, or even more, you can sell more from the comfort of your own home through a website or ebay !

Or you can just add to your hobby list with the added bonus of being able to make Birthday and Christmas presents !

If you decide to purchase, I really wish you the best of luck with this amazing skill that has seen me through all these years..

Get it HERE

All the best,
Cornelius

Currently have 0 comments:


Post a Comment

Subscribe to: Post Comments (Atom)

Announcing - A Quick and Easy way to start making money fast !